Tupolev 154M noise asesment (Анализ шумовых характеристик самолёта Ту-154М)
| Категория реферата: Рефераты по авиации и космонавтике
| Теги реферата: шпаргалки по математике, сочинение
| Добавил(а) на сайт: Demenok.
Предыдущая страница реферата | 1 2 3 4 5 6 7 | Следующая страница реферата
In judging the overall usefulness of any jet noise reduction system, several factors must be considered in addition to the amount of noise reduction. Among these factors are loss of thrust, addition of weight, and increased fuel consumption.
A number of noise-suppression schemes have been studied, mainly for
turbofan engines of one sort or another. These include inverted-temperature-
profile nozzles, in which a hot outer flow surrounds a cooler core flow, and mixer-ejector nozzles. In the first of these, the effect is to reduce
the overall noise level from that which would be generated if the hot outer
jets are subsonic with respect to the outer hot gas. This idea can be
implemented either with a duct burner on a conventional turbofan or with a
nozzle that interchanges the core and duct flows, carrying the latter to
the inside and the former to the outside. In the mixer-ejector nozzle, the
idea is to reduce the mean jet velocity by ingesting additional airflow
through a combination of the ejector nozzles and the chute-type mixer.
Fairly high mass flow ratios can be attained with such arrangements, at the
expense of considerable weight.
The most promising solution, however, is some form of “variable cycle” engine that operates with a higher bypass ratio on take-off and in subsonic flight than at the supersonic cruise condition. This can be achieved to some degree with multi-spool engines by varying the speed of some of the spools to change their mass flow, and at the same time manipulating throttle areas. Another approach is to use a tandem-parallel compressor arrangement, where two compressors operate in parallel at take-off and subsonically, and in series at a supersonic conditions.
7.1.1 Duct Linings
It is self evident that the most desirable way to reduce engine noise would be to eliminate noise generation by changing the engine design. The current state of the art, however, will not provide levels low enough to satisfy expected requirements; thus, it is necessary to attenuate the noise that is generated.
Fan noise radiated from the engine inlet and fan discharge (Fig. 7.1) of current fan jet airplanes during landing makes the largest contribution to perceived noise.
[pic]
Figure 7.1 Schematic illustration of noise sources from turbofan engines
Figure 7.2. shows a typical farfield SPL noise spectrum generated by a turbofan engine at a landing-approach power setting. Below 800 Hz, the spectrum is controlled by noise from the primary jet exhaust. The spectrum between 800 and 10000 Hz contains several discrete frequency components in particular that need to be attenuated by the linings in the inlet and the fan duct before they are radiated to the farfield.
[pic]
Figure 7.2 Engine-noise spectrum
The objective in applying acoustic treatment is to reduce the SPL at the characteristic discrete frequencies associated with the fan blade passage frequency and its associated harmonics. Noise reductions at these frequencies would alleviate the undesirable fan whine and would reduce the perceived noise levels.
A promising approach to the problem has been the development of a
tuned-absorber noise-suppression system that can be incorporated into the
inlet and exhaust ducts of turbofan engines. An acoustical system of this
type requires that the internal aerodynamic surfaces of the ducts be
replaced by sheets of porous materials, which are backed by acoustical
cavities. Simply, these systems function as a series of dead-end
labyrinths, which are designed to trap sound waves of a specific
wavelength. The frequencies for which these absorbers are tuned is a
function of the porosity of flow resistance of the porous facing sheets and
of the depth or volume of the acoustical cavities. The cavity is divided
into compartments by means of an open cellular structure, such as honeycomb
cells, to provide an essentially locally reacting impedance (Fig. 7.3).
This is done to provide an acoustic impedance almost independent of the
angle of incidence of the sound waves impinging on the lining.
The perforated-plate-and-honeycomb combination is similar to an array of Helmholtz resonators; the pressure in the cavity acts as a spring upon which the flow through the orifice oscillates in response to pressure fluctuations outside the orifice.
[pic]
Figure 7.2 Schematic of acoustic damping cavities in an angine duct. The size of the resonators is exaggerated relative to the duct diameter.
The attenuation spectrum of this lining is that of a sharply tuned resonator effective over a narrow frequency range when used in an environment with low airflow velocity or low SPL. This concept, however, can also provide a broader bandwidth of attenuation in a very high noise- level environment where the particle velocity through the perforations is high, or by the addition of a fine wire screen that provides the acoustic resistance needed to dissipate acoustic energy in low particle-velocity or sound-pressure environments. The addition of the wire screen does, however, complicate manufacture and adds weight to such an extent that other concepts are usually more attractive.
[pic]
Figure 7.3 Acoustical lining structure.
Although the resistive-resonator lining is a frequency-tuned device absorbing sound in a selected frequency range, a suitable combination of material characteristics and lining geometry will yield substantial attenuation over a frequency range wide enough to encompass the discrete components and the major harmonics of most fan noise.
7.1.2 Duct Lining Calculation
First we have to determine the blade passage frequency:
[pic], where z is number of blades, n is RPM.
Blade passage frequencies for different engine modes are given in table 7.1
Next we determine the second fan blade passage harmonic frequency, which is
two times greater than the first one: [pic].
Table 7.1 Fan blade passage frequencies for different engine modes.
|Take-off |Nominal |88%Nom |70%Nom |60%Nom |53%Nom |Idle | |RPM |10425
|10055 |9878 |9513 |9315 |8837 |4000 | |1st harmonic freq., Hz |5386,25
Рекомендуем скачать другие рефераты по теме: шпаргалки по истории россии, скачать дипломную работу.
Категории:
Предыдущая страница реферата | 1 2 3 4 5 6 7 | Следующая страница реферата